[Answer ID: 15471]

What does the message on the LCD display indicate when the INFO LED is turned on? (TS3000 series)

Created 08/25/2014 15:31  |   Updated 08/25/2014 15:33

After you change settings or format a hard drive, the current status is displayed on the LCD.

LCD Message

Description

Corrective Action

HDx Warning I11
Bad Sectors

The bad sectors in hard drive X may have reached a dangerous level.

Replace hard drive X.

Operation I12
DEGRADE MODE

Operating in degraded mode.

-

RAID I13
ARRAYxFormatting

Formatting RAID array X.

-

RAID I14
ARRAYx Checking

Checking RAID array X.

-

RAID I15
ARRAYx Scanning

Examining the error status of RAID array X.

-

RAID I16
ARRAYx Creating

Creating RAID array X.

-

RAID I17
ARRAYx Resyncing

Resynchronizing RAID array X.

-

RAID I18
ARRAYx Rebuilding

Rebuilding RAID array X.

-

RAID I19
ARRAYx 0 Filling

Writing 0s to RAID array X, erasing all data.

-

RAID I20
DISKx Formatting

Formatting hard drive X.

-

RAID I21
DISKx Checking

Checking hard drive X.

-

RAID I22
DISKx 0 Filling

Erasing the data for hard drive X.

-

SYSTEM I25
F/WUPDATING

Updating the TeraStation firmware.
Note: Do not turn off the power during the updating process.

-

Web Setting I26
Initializing

Initializing all settings.

-

USB Diskx I27
Checking

Checking USB hard drive X.

-

USB Diskx I28
Formatting

Formatting USB hard drive X.

-

Press FuncSW I31
New Diskx ready

Displayed when pressing the Function button to rebuild the RAID after replacing hard drive X.

Press the Function button to rebuild the RAID array.

Set From Web I32
New Diskx ready

Displayed after replacing hard drive X when the RAID needs to be rebuilt in Settings or formatting is necessary.

In Settings, either rebuild the RAID array or format the hard drive.

Replication I33
ReplicateFailure

An error occurred in replication, or synchronization between the main TeraStation and the backup TeraStation failed during failover configuration.

In Settings, navigate to Backup - Replication and choose “Resync” to execute resynchronization. If the error is displayed again, contact Buffalo technical support for assistance.

Virus alert I34
Virus detected

A virus scan found a virus.

Once the virus is removed from the quarantine folder, the message is no longer displayed. If the antivirus software is configured to delete viruses from the quarantine folder automatically, then the message will not be displayed.

Cartridgex I35
Location error

A hard drive set as a media cartridge has been installed in the drive 1 slot.

Connect to the slot that was set as a media cartridge.

Cartridgex I36
Decryption error

Media cartridge cannot be decrypted. The media cartridge may have been encrypted by a TeraStation other than this product.

Connect to the TeraStation that performed encryption to decrypt.

Recovery I37
SystemRecovering

System recovery in progress.

-

Recovery I38
RecoveryFinished

System recovery is complete.

-

Recovery I39
Change Boot

System recovery from the USB recovery device is complete.

Change the boot mode switch on the rear to HDD.

Recovery I40
DataWillDeleted

Beginning recovery. All data on the drive in Disk 1 will be deleted.

-

Recovery I41
PushFuncToStart

Pressing the Function button on the front will start the recovery process.

-

Recovery I42
Preparing

Preparing to start the recovery process.

-

Recovery I43
Unsupported HW

The TeraStation was started from the USB recovery device, but the system cannot be recovered from this USB recovery device.

-

Recovery I44
Disk1 not found

Recovery from the USB recovery device was initiated, but Disk 1 was not detected.

Make sure that Disk 1 is present and fully inserted in its slot.

Recovery I45
Recovery Failed

Recovery failed.

-

RAID ARRAY I46
RMM+Processing

Data migration or conversion (RAID migration) is in progress.

Do not turn off the TeraStation power.

SYSTEM I47
Don’t Power Off

FailOver I48
PushFuncToStart

This TeraStation is ready to become the failover backup for the main TeraStation.

Hold down the Function button on the front of the target TeraStation until it stops beeping to accept failover backup status.

FailOver I49 LostMainTarget

The main TeraStation in the failover configuration cannot be found.

Make sure that the main TeraStation is on, working, and connected to the network.

FailOver I50
Maintenance mode

Failover maintenance is in progress.

Do not turn off the TeraStation power.

FailOver I51
Initializing

Initializing the failover configuration.

Do not turn off the TeraStation power.

New Firmware I52
Available

A new firmware version has been released.

Update the firmware.

BackupTask xx I54
Backup Failure

xxth backup task has been failed.

Make sure xxth backup task is configured correctly. (“xx” is backup task number.) The LinkStation or TeraStation may be in standby mode. Start the NAS on. If the backup task still fails, check the status of NAS, network, and backup source or destinations.

Recovery I55
RecoveryAuthFail

Authentication during recovery of settings failed.

Settings can only be restored for the TeraStation whose settings were originally saved. To restore settings, insert the USB memory device, move the Boot Mode switch on the rear of the TeraStation to the USB position, and restart the TeraStation. Or, settings can be restored from Settings with the TeraStation powered on.

Surveillance I56
Lack of License

There are not enough surveillance camera server licenses.

Purchase and register an additional license.

Surveillance I57
No free space

There is not enough space to save additional surveillance video.

Delete or move some of the stored video.

Surveillance I58
Recording Failure

Video not recorded.

Check your settings. Also, use the utilities provided with your camera to check that the camera is operating correctly.



Details


Products

OS / Hardware

Was this answer helpful?
Please tell us how we can make this answer more useful.

Refine your search

Select Product / OS & Hardware

      Enter Keywords or a specified ID